API 5CT 13Cr

API 5CT 13Cr

Brief Introduction to the Core Features of API 5CT 13Cr
API 5CT 13Cr is a martensitic stainless steel oil country tubular goods (OCTG) grade under the American Petroleum Institute (API) Specification 5CT, corresponding to the L80-13Cr group. It has a minimum yield strength of 80,000 psi (552 MPa) and a minimum tensile strength of 95,000 psi (655 MPa). API 5CT is the internationally recognized specification for OCTG; the 13Cr grade is specified to be manufactured by the seamless process, suitable for drilling, completion and production operations in oil and gas wells.
The core feature of API 5CT 13Cr is the balanced combination of strength and corrosion resistance. Produced by the quench-and-temper (QT) process, it exhibits a uniform tempered martensitic microstructure with approximately 13% chromium, providing excellent resistance to CO₂ corrosion while guaranteeing a yield strength of 552 MPa. As a representative corrosion-resistant alloy (CRA) grade in API 5CT and one of the workhorse grades for CO₂-containing oil and gas wells, it is widely used for tubing, casing and couplings in CO₂-bearing and high-pressure gas wells.
API 5CT 13Cr covers two product specification levels, PSL1 and PSL2. PSL1 is the base level with broader chemical composition and mechanical property requirements, suitable for conventional well conditions; PSL2 is the enhanced level with stricter requirements on impact toughness and non-destructive testing, suitable for CO₂-containing sour service environments. The product conforms to API Specification 5CT, ISO 11960 and GB/T 19830. 13Cr is the corrosion-resistant alloy grade (L80-13Cr) within API 5CT; in addition, some mills have developed the Super 13Cr improved grade, which is outside the scope of API 5CT, offers higher corrosion resistance and suits environments with high CO₂ plus small amounts of H₂S.
Send Inquiry
Description
Technical Parameters

Products Features

High-Temperature Oxidation Resistance

High Strength and Good Toughness (Core Advantage)

The core advantage of API 5CT 13Cr lies in the balance between medium-high strength and good toughness. Thanks to the QT heat treatment (quench + temper) and the martensitic stainless steel design with 13% chromium, 13Cr maintains good impact toughness while guaranteeing a minimum yield strength of 552 MPa and a minimum tensile strength of 655 MPa. Its yield strength is the same as L80 (552 MPa), but 13Cr offers excellent resistance to CO₂ corrosion, making it suitable for CO₂-containing oil and gas well environments.

Performance indicators

PSL1 Requirements

PSL2 Requirements

Minimum Yield Strength (MPa)

552

552

Maximum Yield Strength (MPa)

655

655

Minimum Tensile Strength (MPa)

655

655

Maximum Tensile Strength (MPa)

-

760

Yield strength ratio

Usually ≤ 0.90

Usually ≤ 0.90

Elongation

≥ 15-18%

≥ 15-18%

Note: The strength level of 13Cr is the same as L80 and lower than P110. For CO₂-containing oil and gas wells, 13Cr is the first-choice grade; for environments with high CO₂ plus small amounts of H₂S, Super 13Cr is recommended; for high-H₂S environments, 22Cr or 25Cr duplex stainless steel is recommended. 

High-Temperature Corrosion Resistance

Welding Process Requirements (Strict Preheating and Post-Weld Heat Treatment Required)

The welding requirements of 13Cr martensitic stainless steel are more stringent than those of carbon steel. With a carbon content of 0.15–0.22% and a chromium content of 12–14%, the preheating temperature, interpass temperature and heat input must be controlled during welding, and post-weld heat treatment must be performed as required to ensure the strength, toughness and corrosion resistance of the weld and heat-affected zone (HAZ).

Key welding points:

  • Preheating and interpass temperature control: 13Cr requires preheating to 150–250℃ and control of the interpass temperature to reduce the risk of cold cracking.
  • Control of harmful elements: P and S contents are kept within the normal range to ensure the cleanliness of the weld and base metal.
  • Process applicability: Suitable for field butt welding (girth welding) and other processes, provided that preheating and post-weld heat treatment are strictly performed.

For the 13Cr grade, a preheating temperature of 150–250℃ is recommended for welding; for thick-wall pipes or highly restrained joints, a higher preheating temperature is recommended.

Note: Weld and HAZ hardness ≤23 HRC shall be maintained to restore corrosion resistance. Post weld heat treatment is mandatory only for thick walled /highly restrained joints.

High Stability

Good Toughness and Resistance to Brittle Fracture

API 5CT 13Cr PSL2 requires Charpy V-notch impact testing to ensure resistance to brittle fracture under service conditions. The tempered martensitic microstructure obtained by the QT heat treatment significantly enhances the toughness of the material, enabling 13Cr OCTG to be reliably applied in CO₂-containing oil and gas well environments.

Typical impact toughness requirements (PSL2):

  • Test temperature: usually 0°C or lower (per customer requirement)
  • Minimum impact energy: ≥ 27 J (average) / ≥ 20 J (single value)
Good Processability

Good Corrosion Resistance and Environmental Adaptability

API 5CT 13Cr offers good resistance to general corrosion in normal atmospheric, fresh water, soil and oil and gas media. In CO₂-containing service environments, 13Cr exhibits excellent CO₂ corrosion resistance and is the first-choice grade for CO₂-bearing oil and gas wells. For H₂S-bearing environments, conventional 13Cr is suitable for low-H₂S service, Super 13Cr for high CO₂ plus small amounts of H₂S, and 22Cr or 25Cr duplex stainless steel is recommended for high-H₂S environments.

High-Temperature Oxidation Resistance

Good Cold Bending and Processing Performance

API 5CT 13Cr has a moderate carbon content and a moderate yield-to-tensile ratio (PSL2 usually requires ≤ 0.90), giving it good cold bending formability. It is suitable for the production of cold-bent pipes and hot-bent elbows via hot bending processes. In terms of end finishing, 13Cr OCTG can be threaded, upset and bevelled to meet API 5CT requirements for threads and couplings.

Technical Specifications

Chemical Composition (API Spec 5CT / ISO 11960)

 

Element

PSL1

PSL2

Note

C

0.15–0.22%

0.15–0.22%

Carbon control for weldability

Mn

0.25–1.00%

0.25–1.00%

Solid-solution strengthening

P

≤ 0.020%

≤ 0.020%

Harmful element, strictly controlled

S

≤ 0.010%

≤ 0.010%

Harmful element, strictly controlled

Si

≤ 1.00%

≤ 1.00%

Deoxidizer, improves strength

Cr

12.0–14.0%

12.0–14.0%

Corrosion resistance against CO₂

Ni

≤ 0.50%

≤ 0.50%

Improves toughness

Mo

≤ 0.50%

≤ 0.50%

Improves corrosion resistance

Physical Properties

 

Property

Value/Range

Test Conditions

Density

≈ 7.80 g/cm³

Room temperature (20℃)

Melting point

≈ 1420–1460℃

-

Modulus of elasticity

≈ 207 GPa

Room temperature

Thermal conductivity

≈ 25 W/(m·K)

Room temperature

Thermal expansion coefficient (20–100℃)

≈ 10.5 × 10⁻⁶ /K

-

Poisson's ratio

≈ 0.28

Room temperature

Mechanical Properties (Typical Values)

 

Property

PSL1

PSL2

Standard

Minimum yield strength

552 MPa

552 MPa

API Spec 5CT / ISO 11960

Maximum yield strength

655 MPa

655 MPa

API Spec 5CT / ISO 11960

Minimum tensile strength

655 MPa

655 MPa

API Spec 5CT / ISO 11960

Maximum tensile strength

-

≤ 760 MPa

API Spec 5CT / ISO 11960

Elongation

≥ 15%

≥ 15%

API Spec 5CT

Note: In API 5CT 13Cr, "13Cr" refers to a chromium content of approximately 13%, classified as martensitic stainless steel. Its yield strength is 552 MPa (same as L80) and its tensile strength is 655 MPa. 13Cr is the corrosion-resistant alloy grade (L80-13Cr) within API 5CT; Super 13Cr is an improved grade developed by mills and falls outside the scope of API 5CT, offering higher corrosion resistance.

Applicable Media

 

1. Oil and Natural Gas:
Tubing, Casing, and Couplings for CO₂-Containing Oil and Gas Wells
2. High-pressure oil and gas wells:
Deep wells containing CO₂, high-pressure wells
3. General Fluids:
Conventional Well Completion and Oil Production Operations

Note: API 5CT 13Cr is suitable for CO₂-containing sour oil and gas environments. For low-H₂S service, conventional 13Cr can be used; for high CO₂ plus small amounts of H₂S, Super 13Cr is recommended; for high-H₂S service, 22Cr/25Cr duplex stainless steel or nickel-based alloys are required.

Product Forms and Manufacturing Process

 

Seamless Steel Pipe (Seamless)
• Process: hot rolling + piercing + elongation rolling + QT heat treatment (quench + temper)
• OD range: 114.3–508 mm (4-1/2″–20″)
• Wall thickness range: 5.21–16.13 mm
• Features: weld-free with high pressure capacity, suitable for CO₂-containing deep and high-pressure oil and gas wells
• Typical applications: tubing and casing for CO₂-containing wells, high-pressure wells, wellhead gathering lines

Applicable Standards and Delivery Condition

 

• Standards: API Spec 5CT, ISO 11960, GB/T 19830
• Product specification levels: PSL1 (base level), PSL2 (enhanced level)
• Delivery condition: QT (quench + temper)
• End finishing: plain end, beveled end, threaded end (STC, LTC, BTC), special threaded end
• Certification: for PSL2 requirements, a certificate of conformance (SR15.1 mandatory) and full traceability (SR15.2 mandatory) must be provided

Heat Treatment System and Welding Points

 

The final properties of API 5CT 13Cr depend on the QT heat treatment process:
1. QT Treatment (Quench + Temper, to Obtain Tempered Martensitic Microstructure)

Austenitize by heating to 950–1000℃, then quench in water or oil, followed by tempering at 550–650℃ for 1–2 hours. This produces a uniform tempered martensitic microstructure, ensuring a balanced combination of strength and toughness and meeting CO₂ corrosion resistance requirements.
2. Post-Weld Heat Treatment (If Required)
If stress relief is required after girth welding of pipes, tempering at 600–700℃ for 1–2 hours may be performed. The heating and cooling rates during post-weld heat treatment must be controlled to avoid affecting the microstructure and properties of the base metal.

Important reminders:
• 13Cr is the recommended corrosion-resistant grade in CO₂-containing oil and gas service environments; hardness must be controlled after welding
• for H₂S-bearing environments, conventional 13Cr is suitable for low-H₂S service; high-H₂S environments require Super 13Cr, 22Cr or 25Cr
• heat input and interpass temperature must be strictly controlled during welding to avoid grain coarsening and hardness exceeding limits in the HAZ

API 5CT 13Cr is suitable for tubing, casing and couplings in CO₂-containing oil and gas wells and is recommended for:

 

Application Fields

  •  

    • Oil and gas drilling
    • Tubing and casing for CO₂-containing oil and gas wells
    • High-pressure oil and gas wells
    • Completion and production operations in conventional oil and gas wells
    • Wellhead equipment and gathering lines

Delivery and Customization

We provide flexible and reliable supply chain solutions to ensure you obtain API 5CT 13Cr OCTG that exactly matches your project requirements.
Customizable Material Forms
We support the production of various base and special forms to drawings or specifications.

Form

Seamless Pipe

Conventional Range

Outer diameter: 114.3–508 mm; Wall thickness: 5.21–16.13 mm

Customization Capability

Hot-rolled seamless pipes, fixed-length cutting, bevel processing, pipe end threads, special heat treatment conditions

Why Choose Us? - Reliable Engineering Technology. Dependable Delivery.

We are not just a supplier, but a trusted materials partner for you in China.

Sample Support & Quick Response

Vertically Integrated Production

Own 20,000㎡ facility with 10+ automated lines (8,000+ tons/year). In-house tooling & die center enables rapid customization and effective cost control - no middleman markup.

Full Traceability

Strict Quality Control at Every Stage

Full traceability across key QC checkpoints throughout production. 100% compliant with ASTM/ASME, EN, and GB standards. Material test reports available with every shipment.

Professional Logistics & Packaging

Reliable Delivery & Export Packaging

10+ years exporting to Europe, North America, Southeast Asia & Middle East with waterproof and anti-rust protection, combined with flexible shipping options ensures safe and on-time arrival.

Complete Export Documentation

Sample Validation Before Mass Production

We provide free samples for quality verification, allowing you to place bulk orders only after approval. We ensure consistency from sample to mass production by accurate dimensional measurement and transparent manufacturing.

Summary of Core Advantages

Medium-high strength matched with good toughness

Minimum yield strength of 552 MPa, minimum tensile strength of 655 MPa, along with good impact toughness, making it suitable for oil and gas well environments containing CO₂.

Excellent CO₂ Corrosion Resistance

With a chromium content of approximately 13%, 13Cr exhibits excellent resistance to CO₂ corrosion, making it the preferred steel grade for oil and gas wells containing CO₂.

Good welding performance

Designed with a moderate carbon equivalent (CEIIW ≤ 0.45), it exhibits excellent field ring welding construction performance. The toughness and resistance to cold cracking in the heat-affected zone of the weld are good.

High Cost-Effectiveness

13Cr is the leading alloy grade of corrosion-resistant alloys (CRA) in API 5CT. It offers excellent corrosion resistance at a moderate cost, making it an economical and efficient choice for oil and gas wells containing CO₂.

Diverse product forms

In accordance with API 5CT requirements, only seamless pipes with an outer diameter range of 114.3–508 millimeters shall be used.

Compliant with multiple international standards

API Spec 5CT, ISO 11960, GB/T 19830, etc.

 

 

FAQ

Q: What is the difference between API 5CT 13Cr PSL1 and PSL2? How to choose?

 

Q: What are the differences between API 5CT J55, K55, N80-1, N80Q, L80-1, P110 and 13Cr? How to choose?

 

Q: What is the maximum service temperature of API 5CT 13Cr?

 

Q: What about the weldability of API 5CT 13Cr?

 

Q: How is the corrosion resistance of API 5CT 13Cr?

 

Q: Can API 5CT 13Cr replace ASTM A53 or J55?

 

 

Hot Tags: api 5ct 13cr, China api 5ct 13cr manufacturers, suppliers, factory