API 5CT N80Q

API 5CT N80Q

Brief Introduction to the Core Features of API 5CT N80Q
API 5CT N80Q is a high-strength quenched and tempered oil casing steel grade specified in the API Spec 5CT standard. It has a minimum yield strength of 80,000 psi (552 MPa), a maximum yield strength of 110,000 psi (758 MPa), and a minimum tensile strength of 100,000 psi (689 MPa). API 5CT is an internationally recognized standard for oil and casing pipes. The API 5CT standard permits N80-Q to use ERW (Electric Resistance Welded) straight-seam resistance-welded pipes, with the requirement that the welded pipes must undergo overall tempering treatment for the entire tube. In the commercial market, N80-Q is almost entirely supplied as seamless pipes. It is suitable for medium-deep and deep wells with high requirements for toughness, as well as high-pressure oil and gas drilling, completion, and production operations in environments without hydrogen sulfide.
N80Q is produced using a quenching and tempering process, with a tempered martensite microstructure. It does not possess resistance to hydrogen sulfide (H₂S) sulfide stress cracking (SSCC) and is therefore not suitable for sour wells containing hydrogen sulfide. The basic supply grade of N80Q is PSL1; PSL2 is an additional upgraded requirement specified in Annex H. Implementation of PSL2 requires explicit stipulation in the purchase contract and is not supplied by default. It is applicable to conventional sweet well conditions without sulfur, where high toughness is required. The product complies with API Spec 5CT, ISO 11960, and GB/T 19830.
Note: N80Q is not suitable for H₂S acidic service conditions; for wells with hydrogen sulfide acidic environments, it is recommended to select anti-sulfur steel grades such as L80-1, C90, and T95.
Send Inquiry
Description
Technical Parameters

Products Features

High-Temperature Oxidation Resistance

Comprehensive performance combining high strength and high toughness (core advantage)

N80Q Core Advantages: It undergoes tempering, quenching, and tempering treatment to obtain tempered martensite microstructure. Its yield strength and tensile strength are consistent with N80-1, but its low-temperature impact toughness is significantly superior to normalized N80-1. It is designed for medium-deep and deep high-pressure oil and gas wells without sulfur, suitable for service conditions requiring toughness and resistance to brittle fracture. According to API 5CT standards, N80-Q allows the use of ERW straight-seam resistance-welded pipes, but requires the welded pipes to undergo overall full-pipe tempering treatment. In the commercial market, N80-Q is almost entirely supplied as seamless pipes.

Performance indicators

PSL1 Requirements

Minimum Yield Strength (MPa)

552

Maximum Yield Strength (MPa)

758

Minimum Tensile Strength (MPa)

689

Maximum Tensile Strength (MPa)

-

Yield strength ratio

No mandatory requirements

Elongation

Calculate and determine using the tabular formula from API Spec 5CT

High-Temperature Corrosion Resistance

Good welding performance (core requirement for casing and tubing)

API 5CT N80Q pipe is subjected to quenching and tempering heat treatment. There is a risk of hardening in the welding heat-affected zone, so the welding process requirements for N80Q are higher than those for normalized N80-1/J55/K55. It meets the requirements for on-site construction and coupling welding. The carbon content of N80Q is generally ≤0.43%, and the manganese content is controlled in accordance with API specifications.

Key Welding Points:

  • Strictly implement WPS welding procedure qualification, control heat input, reduce the hardening tendency of the heat-affected zone, and minimize the risk of cold cracks.
  • Strictly control harmful impurities P and S to ensure the purity of the base material and weld seam

Important Reminder:
N80Q is a quenched and tempered high-strength carbon steel with strict welding process requirements. For thick-walled joints, preheating is recommended at 100-150°C. This is an engineering practice experience value; the API standard does not mandate preheating temperature, and actual operations should follow the WPS (Welding Procedure Specification) welding procedure qualification. The base metal itself does not have sulfide stress cracking resistance, and the weld is also not sulfide-resistant. The toughness of the welding heat-affected zone will decrease. 

High Stability

Good toughness and resistance to brittle fracture

N80Q is only PSL1 grade. Under API standards, PSL1 does not require Charpy impact testing; PSL2 (after Annex H is activated) requires Charpy impact testing. It has a tempered martensitic matrix microstructure, offering better low-temperature toughness than N80-1, meeting the service requirements for medium-deep wells and high-pressure, non-sulfur oil and gas wells. Impact test indicators need to be agreed upon in the contract for low-temperature severe service conditions.

Typical impact requirements (to be implemented only if agreed in the contract or Annex H is activated):

  • Test Temperature: According to the user's project requirements
  • Impact energy: as agreed in the procurement agreement
Good Processability

Good corrosion resistance and environmental adaptability

API 5CT N80Q is a general quenched and tempered carbon steel oil casing, which has uniform corrosion resistance in atmospheric, fresh water, soil, and dry non-sulfur oil and gas media. It cannot be used in H₂S acidic oil and gas environments; for CO₂ corrosion conditions, corrosion rate assessment is required, and 13Cr corrosion-resistant alloy should be selected for severe corrosion environments.
Note: N80Q is a quenched and tempered high-strength carbon steel, not a sour service steel; once the medium contains hydrogen sulfide, there is a risk of sulfide stress cracking failure.

High-Temperature Oxidation Resistance

Good cold bending and processing performance

API 5CT N80 Q is a quenched and tempered seamless steel pipe.Cold bending requires strict control of deformation; hot bending can be used to manufacture elbows. The pipe ends support thread rolling, upsetting, and beveling. They can be processed into STC/LTC/BTC and Premium special thread connections, meeting the API 5CT thread and coupling technical requirements.

Technical Specification

Chemical Composition(API Spec 5CT / ISO 11960)

 

Element

PSL1

Note

C

≤ 0.43%

Control the carbon content to balance strength, toughness, and weldability

Mn

≤ 1.60%

Solid solution strengthening, enhancing strength and toughness

P

≤ 0.030%

Harmful impurities, strictly controlled

S

≤ 0.030%

Harmful impurities, strictly controlled

Si

≤ 0.45%

Deoxidation, reinforced matrix

CEIIW

No mandatory requirements

 

Physical Properties

 

Property

Value/Range

Test Conditions

Density

≈ 7.85 g/cm³

Room Temperature (20°C)

Melting Point

≈ 1420–1460℃

---

Elastic modulus

≈ 207 GPa

Room Temperature

Thermal Conductivity

≈ 47 W/(m·K)

Room Temperature

Coefficient of Thermal Expansion (20-100°C)

≈ 12.0 × 10⁻⁶ /K

---

Poisson's ratio

≈ 0.28

Room Temperature

Mechanical Properties (Typical value N80Q)

 

Performance

PSL1

Implementation standards

Minimum Yield Strength

552 MPa

API Spec 5CT / ISO 11960

Maximum Yield Strength

758 MPa

API Spec 5CT / ISO 11960

Minimum Tensile Strength

689 MPa

API Spec 5CT / ISO 11960

Maximum Tensile Strength

-

API Spec 5CT / ISO 11960

Elongation

Calculate and determine using the tabular formula from API Spec 5CT

API Spec 5CT

Note: The '80' in N80Q represents a minimum yield strength of 80,000 psi (552 MPa), with the numerical unit being ksi (kilo-pounds per square inch). The actual yield strength range of the pipe material is 552-758 MPa, and the minimum tensile strength is 689 MPa. The heat treatment is quenching and tempering (solution treatment + tempering), which differs from the normalization process of N80-1.

Applicable Media

 

• Petroleum, Natural Gas:
Medium-deep and Deep Well Tubing, Casing and Couplings (Non-H₂S Sweet Wells, with Requirements for Toughness)
• High-pressure oil and gas wells:
Conventional non-sulfur, moderate CO₂ wells, medium-deep and deep wells requiring higher resistance to brittle fracture
• General Fluids:
Well Completion and Oil Production Operations for Sulfur-Free Oil and Gas Wells

Note: API 5CT N80Q is not suitable for H₂S-containing acidic oil and gas conditions; for H₂S-containing conditions, API 5CT sour-resistant steel grades L80-1, C90, T95 or corrosion-resistant alloys 13Cr, 22Cr should be selected.

Product Form and Manufacturing Process

 

Seamless steel pipe (Seamless)
• Process: Hot rolled piercing + Extension Rolling + Tempering (Quenching + Tempering) Heat Treatment
• Outer Diameter Range: 114.3–508 mm (4-1/2"–20")
• Wall thickness range: 5.21–16.13 mm
• Features: Tempered martensite microstructure, which has high strength and better low-temperature toughness than N80-1; suitable for medium-deep and deep high-pressure non-sulfur oil and gas wells, and appropriate for projects with requirements for resistance to brittle fracture.
• Medium-deep wells, deep well downhole tubing and casing; downhole wellhead connection components

 

Applicable Standards and Delivery Condition
• Standard: API Spec 5CT,ISO 11960,GB/T 19830
• Product Specification Level: Default to PSL1 (Basic Level); PSL2 is an annexed upgrade in Annex H, which requires explicit agreement in the contract to enable.
• Delivery Status: Tempered (Quenching + Tempering)
• End Processing: Flat Ends, Beveled Ends, Threaded Ends (STC, LTC, BTC), Premium Special Fitting Ends
• Provide material certificates in accordance with the procurement contract requirements; PSL1 does not have mandatory SR15 certificates and full-process traceability mandatory clauses. Upon activation of Annex H (PSL2), SR15.1 and SR15.2 become mandatory.

Heat Treatment System and Welding Key Points

 

API 5CT N80 Q is delivered in quenched and tempered heat treatment condition, resulting in tempered martensite microstructure to achieve a combination of high strength and good toughness.

1. Tempering treatment
After quenching and high-temperature tempering, tempered martensite structure is obtained, balancing strength and low-temperature toughness.

2. Post-weld heat treatment (if required)

After tempering the base material is welded, the toughness of the heat-affected zone decreases. If stress relief is required, it must be strictly carried out in accordance with the WPS qualification; arbitrary high-temperature tempering should not be performed to avoid damaging the tempered microstructure of the base material.

Important Reminder:
• The base material N80Q does not have sulfide stress cracking resistance and must not be used in H₂S acidic wells.
• Control the welding heat input and interpass temperature in accordance with the WPS welding procedure qualification.

API 5CT N80Q is suitable for medium-deep wells, deep wells, high-pressure, non-sulfur environments, and oil and gas wells requiring high toughness. It is recommended for use in oil pipes, casing, and couplings as follows:

 

Application Fields

  •  

    Oil and Natural Gas Drilling
    • Medium-deep wells, deep well tubing, casing
    • High-pressure, sulfur-free (sweet well) oil and gas wells for applications with requirements on low-temperature toughness
    • Completion and oil production operations for oil and gas wells containing moderate levels of CO₂ and free of H₂S
    • Underground wellhead connection components

Delivery and Customization

We offer flexible and reliable supply chain solutions to ensure you receive API 5CT N80Q oil casing that perfectly matches your project requirements.
Customizable Material Forms
We support producing various basic and special shapes according to drawings or specifications.

Form

Seamless Pipe

Conventional Range

Outer diameter: 114.3–508 mm; Wall thickness: 5.21–16.13 mm

Customization Capability

Hot-rolled seamless pipes, fixed-length cutting, bevel processing, pipe end threads, special heat treatment conditions

Why Choose Us? - Reliable Engineering Technology. Dependable Delivery.

We are not just a supplier, but a trusted materials partner for you in China.

Sample Support & Quick Response

Vertically Integrated Production

Own 20,000㎡ facility with 10+ automated lines (8,000+ tons/year). In-house tooling & die center enables rapid customization and effective cost control - no middleman markup.

Full Traceability

Strict Quality Control at Every Stage

Full traceability across key QC checkpoints throughout production. 100% compliant with ASTM/ASME, EN, and GB standards. Material test reports available with every shipment.

Professional Logistics & Packaging

Reliable Delivery & Export Packaging

10+ years exporting to Europe, North America, Southeast Asia & Middle East with waterproof and anti-rust protection, combined with flexible shipping options ensures safe and on-time arrival.

Complete Export Documentation

Sample Validation Before Mass Production

We provide free samples for quality verification, allowing you to place bulk orders only after approval. We ensure consistency from sample to mass production by accurate dimensional measurement and transparent manufacturing.

Summary of Core Advantages

High Strength and High Toughness

Minimum yield strength 552 MPa, maximum yield 758 MPa, minimum tensile strength 689 MPa; tempered martensite, with toughness superior to N80-1, suitable for medium-deep to deep wells, high-pressure non-sulfur environments, and sweet wells requiring resistance to brittle fracture.

01

Quenching and Tempering Delivery

Tempered martensite microstructure; different from N80-1 hot-rolled normalized carbon steel.

02

Controllable Machining Performance

Supports standard API threads and Premium gas-tight special connections; heat-treated steel welding requires strict process control, with reduced toughness in the heat-affected zone.

03

Supply Form

Supply form: Seamless pipe dominates commercial supply. ERW pipe is permitted per API 5CT for N80 Q and shall be fully quenched and tempered, while ERW product is barely available on market. Outer diameter coverage: 114.3 508 mm.

04

Complies with Multiple International Standards

Such as API Spec 5CT, ISO 11960, GB/T 19830, etc.

05

 

 

FAQ

Q: Does API 5CT N80Q have PSL2? How to select it?

 

Q: What are the differences between API 5CT J55, K55, N80-1,N80Q, L80-1, and P110? How to choose?

 

Q: What is the maximum operating temperature for API 5CT N80Q?

 

Q: What is the welding performance of API 5CT N80Q?

 

Q: What is the corrosion resistance of API 5CT N80Q?

 

Q: Can API 5CT N80Q replace ASTM A53?

 

 

Hot Tags: api 5ct n80q, China api 5ct n80q manufacturers, suppliers, factory