Products Features

Balanced strength and high cost-effectiveness (core advantage)
The core advantages of K55: It has the same yield strength as J55 but higher tensile strength and better collapse resistance than J55. It is an optimal choice for shallow, medium-shallow to medium-deep conventional oil and gas wells without strong corrosive media, balancing performance and cost. When combined with the ERW (Electric Resistance Welding) process, it offers high dimensional accuracy and uniform wall thickness, providing a good cost advantage over seamless pipes.
|
Performance indicators |
PSL1 Requirements |
|
Minimum Yield Strength (MPa) |
379 |
|
Maximum Yield Strength (MPa) |
552 |
|
Minimum Tensile Strength (MPa) |
655 |
|
Maximum Tensile Strength (MPa) |
- |
|
Yield strength ratio |
No mandatory requirements |
|
Elongation |
Calculate and determine using the tabular formula from API Spec 5CT |
Note: The K55 yield strength range is the same as J55, but its minimum tensile strength is higher than J55; however, its strength is lower than N80, L80, and P110. It is suitable for medium-shallow to medium-deep wells and low-to-medium pressure oil and gas wells. It is not applicable to H₂S acidic environments; for acidic service conditions, sulfide-resistant grade steels should be selected.

Good welding performance (core requirement for casing and tubing)
The carbon equivalent design of API 5CT K55 ensures good welding performance, which is a fundamental requirement for field construction and coupling welding of oil casing. The carbon content of K55 is typically controlled to ≤ 0.40%, and the manganese content to ≤ 1.60%, ensuring good toughness and resistance to cold cracking in the heat-affected zone under field welding conditions.
Key Welding Points:
- Medium carbon equivalent, reducing the hardening tendency of the heat-affected zone and lowering the risk of cold cracks
- Strictly control harmful impurities P and S to ensure the purity of the base material and weld seam
- It supports seamless pipe butt welding and ERW welded pipe high-frequency welding, and performs well in field ring welding construction.
Note: The upper limit of carbon content in K55 is relatively wide; preheating is generally not required under normal operating conditions. For thick-walled or high-restraint joints, preheating is recommended at 80-120°C. This is an engineering practice experience value. The API standard does not mandate a preheating temperature; actual operations should follow the WPS welding procedure qualification. After welding, control the hardness of the weld seam. K55 is also not recommended for use in acidic H₂S service conditions.

Good toughness and resistance to brittle fracture
K55 is only available in PSL1 grade. The API standard does not mandate Charpy impact testing; impact testing is performed only when explicitly required by the purchase contract. It has a ferrite-pearlite microstructure and is suitable for service in shallow, medium-shallow to medium-deep wells under normal temperature conditions. It is not recommended for use in low-temperature severe service conditions.
Typical impact requirements (to be implemented only when agreed in the contract):
- Test Temperature: According to the user's project requirements
- Impact energy: as agreed in the procurement agreement

Good corrosion resistance and environmental adaptability
API 5CT K55 has uniform corrosion resistance in atmospheric, fresh water, soil, and general oil and gas media. It is not recommended for use in H₂S-containing acidic oil and gas environments; instead, C90/T95 sour service steel grades should be selected. For CO₂ corrosion conditions, an assessment is required, and 13Cr or other corrosion-resistant alloys should be chosen for severe corrosion environments.

Good cold bending and processing performance
API 5CT K55 has a moderate carbon content and good cold bending formability, allowing it to undergo cold bending processing as well as hot bending for elbow fabrication. The pipe ends support threading, upsetting, and beveling, and can be processed with STC/LTC/BTC threads to meet the API 5CT thread and coupling technical requirements.
Technical Specification
Chemical Composition (API Spec 5CT / ISO 11960)
|
Element |
PSL1 |
Note |
|
C |
≤ 0.40% |
Carbon content control to ensure weldability |
|
Mn |
≤ 1.60% |
Solid solution strengthening, improve strength |
|
P |
≤ 0.030% |
Harmful impurities, strictly controlled |
|
S |
≤ 0.030% |
Harmful impurities, strictly controlled |
|
Si |
≤ 0.45% |
Deoxidizer, improve strength |
|
CEIIW |
No mandatory requirements |
ERW products can be arranged according to the agreement |
Physical Properties
|
Property |
Value/Range |
Test Conditions |
|
Density |
≈ 7.85 g/cm³ |
Room Temperature (20°C) |
|
Melting Point |
≈ 1420–1460℃ |
--- |
|
Elastic modulus |
≈ 207 GPa |
Room Temperature |
|
Thermal Conductivity |
≈ 50 W/(m·K) |
Room Temperature |
|
Coefficient of Thermal Expansion (20-100°C) |
≈ 11.5 × 10⁻⁶ /K |
--- |
|
Poisson's ratio |
≈ 0.28 |
Room Temperature |
Mechanical Properties (Typical value)
|
Performance |
PSL1 |
Implementation standards |
|
Minimum Yield Strength |
379 MPa |
API Spec 5CT / ISO 11960 |
|
Maximum Yield Strength |
552 MPa |
API Spec 5CT / ISO 11960 |
|
Minimum Tensile Strength |
655 MPa |
API Spec 5CT / ISO 11960 |
|
Maximum Tensile Strength |
- |
API Spec 5CT / ISO 11960 |
|
Elongation |
Calculate and determine using the tabular formula from API Spec 5CT |
API Spec 5CT |
Note: The 'K55' in API 5CT K55 indicates a minimum yield strength of 55,000 psi (approximately 379 MPa), with the number representing thousands of pounds per square inch (ksi). The actual yield strength of the pipe typically ranges between 400–500 MPa, and the tensile strength ranges between 655–750 MPa.
Applicable Media
1. Oil and natural gas:
Medium-shallow and medium-deep well oil pipes, casing, and couplings
2. Medium and low-pressure oil and gas wells:
Medium-shallow wells, medium-deep wells, low-to-medium pressure oil and gas wells
3. General Fluids:
Conventional Well Completion and Oil Production Operations
Note: API 5CT K55 is not suitable for acidic oil and gas environments containing H₂S. In acidic environments, API 5CT sour-resistant steel grades (such as L80, C90, T95) or corrosion-resistant alloys (e.g., 13Cr, 22Cr) should be selected.
Product Form and Manufacturing Process
Seamless steel pipe (Seamless)
• Process: Hot Rolling Piercing + Extension Rolling
• Outer Diameter Range: 114.3–508 mm (4-1/2"–20")
• Wall thickness range: 5.21–16.13 mm
• Features: Seamless, reliable pressure-bearing capability, with anti-collapse performance superior to J55, suitable for medium-shallow to medium-deep wells and low-to-medium pressure oil and gas wells
• Typical applications: Medium shallow and medium deep well downhole tubing and casing; downhole wellhead joint components
Straight Seam High-Frequency Resistance Welded Pipe (ERW)
• Process: Hot-rolled coil → Cold bending forming → High-frequency resistance welding → Normalizing heat treatment
• Outer Diameter Range: Typically ≤ 508 mm (20\")
• Wall thickness range: Typically ≤ 16 mm
• Features: High dimensional accuracy, high production efficiency, and significant cost advantages
• Typical applications: Shallow wells, medium-shallow wells, medium-deep wells, low-pressure to medium-pressure oil and gas wells, general fluid transmission
• Welding Control: High-frequency welding process, weld seam meets all API 5CT requirements for ERW products
Applicable Standards and Delivery Condition
• Standard: API Spec 5CT,ISO 11960,GB/T 19830
• Product Specification Level: Default to PSL1 (Basic Level); PSL2 is an annexed upgrade in Annex H, which requires explicit agreement in the contract to enable.
• Delivery Condition: Hot Rolling / Normalizing
• End Processing: Flat Ends, Beveled Ends, Threaded Ends (STC, LTC, BTC), Special Fitting Ends
• Certificate: Provide material certificates in accordance with the procurement contract requirements; PSL1 does not have mandatory SR15 certificates or mandatory full-process traceability clauses.
Heat Treatment System and Welding Key Points
API 5CT K55 is delivered in hot-rolled or normalized condition and does not require quenching, tempering, or other heat treatment processes.
1. Normalizing Treatment:
Heat to 850-930°C, then air cool to obtain a ferrite-pearlite microstructure, which balances strength and toughness.
2. Post-weld Heat Treatment (as required):
If stress relief is needed to eliminate residual welding stresses, stress-relief annealing at 550-620°C with a holding time of 1-2 hours can be performed; strictly control the heating and cooling rates to avoid affecting the base material properties.
Important Reminder:
• For general oil and gas operating conditions without H₂S, stress relief heat treatment is generally not required after welding.
• K55 is not suitable for H₂S acidic media. For acidic service conditions, anti-sulfur steel grades C90/T95 should be selected.
• Control the welding heat input and interpass temperature to prevent coarse grain growth and excessive hardness in the heat-affected zone.
API 5CT K55 is suitable for oil tubes, casing, and couplings used in medium-shallow wells, medium-deep wells, and low-to-medium pressure oil and gas wells. The recommended applications are as follows:
Application Fields
-
Oil and Natural Gas Drilling
• Medium shallow and medium deep well oil pipes, casing
• Low-pressure and medium-pressure oil and gas wells
• Conventional oil and gas well completion and oil production operations
• Underground wellhead connection components
Delivery and Customization
We offer flexible and reliable supply chain solutions to ensure you receive API 5CT K55 oil casing that perfectly matches your project requirements.
Customizable material forms
We support producing various basic and special shapes according to drawings or specifications.
|
Form |
Seamless Pipe
|
Straight Seam Electric Resistance Welded Pipe (ERW)
|
|---|---|---|
|
Conventional Range |
Outer diameter: 114.3–508 mm; Wall thickness: 5.21–16.13 mm |
Outer diameter: 114.3–508 mm; Wall thickness: 5.21–16.13 mm |
|
Customization Capability |
Hot-rolled seamless pipes, fixed-length cutting, bevel processing, pipe end threads, special heat treatment conditions |
High-frequency straight-seam welded pipes, fixed-length cutting, bevel processing, coating anti-corrosion treatment |
Why Choose Us? - Reliable Engineering Technology. Dependable Delivery.
We are not just a supplier, but a trusted materials partner for you in China.

Vertically Integrated Production
Own 20,000㎡ facility with 10+ automated lines (8,000+ tons/year). In-house tooling & die center enables rapid customization and effective cost control - no middleman markup.

Strict Quality Control at Every Stage
Full traceability across key QC checkpoints throughout production. 100% compliant with ASTM/ASME, EN, and GB standards. Material test reports available with every shipment.

Reliable Delivery & Export Packaging
10+ years exporting to Europe, North America, Southeast Asia & Middle East with waterproof and anti-rust protection, combined with flexible shipping options ensures safe and on-time arrival.

Sample Validation Before Mass Production
We provide free samples for quality verification, allowing you to place bulk orders only after approval. We ensure consistency from sample to mass production by accurate dimensional measurement and transparent manufacturing.
Summary of Core Advantages
Medium Yield Strength, Higher Tensile Strength, and Comprehensive Cost-performance
Minimum yield strength of 379 MPa, minimum tensile strength of 655 MPa; better collapse resistance than J55, suitable for medium-shallow to medium-deep well and medium-low pressure oil and gas well conditions.
01
Hot-rolled / Normalized Delivery
The microstructure is ferrite-pearlite, suitable for service conditions of conventional medium-shallow to medium-deep wells.
02
Good Welding Performance
Controllable carbon equivalent allows on-site welding of seamless pipes and ERW welded pipes, with excellent field ring welding construction performance.
03
Diverse Product Forms
Seamless and ERW welded pipes are both supplied as standard, with outer diameters ranging from 114.3 to 508 mm.
04
Complies with Multiple International Standards
API Spec 5CT, ISO 11960, GB/T 19830, etc.
05
FAQ
Q: Does API 5CT K55 have PSL2? How to select it?
Q: What are the differences between API 5CT J55, K55, N80-1, L80-1, and P110? How to choose among them?
Q: What is the maximum operating temperature for API 5CT K55?
Q: What is the welding performance of API 5CT K55?
Q: How is the corrosion resistance of API 5CT K55?
Q: Can API 5CT K55 replace ASTM A53 or J55?
Hot Tags: api 5ct k55, China api 5ct k55 manufacturers, suppliers, factory

